SHAPEHOLDER WIP

painless potter

Mitglied
Messages
2,603
Hier mal ein kurzes WIP über die Entstehung eines Shapeholders. Es sind mehr Arbeitsschritte als man denkt...

-Schnittmuster erstellen
-Kontur auf das Leder übertragen
-ausschneiden
-Kanten brechen
-Knickfalz ausdünnen
-Kanten runden
-Naht der Gürtelschlaufe senken und Naht markieren
-Schlaufe ausdünnen
-Leder kurz wässern
 

Attachments

  • P1030377 (Mittel).JPG
    P1030377 (Mittel).JPG
    129.4 KB · Views: 196
  • P1030391 (Mittel).JPG
    P1030391 (Mittel).JPG
    110.1 KB · Views: 170
  • P1030390 (Mittel).JPG
    P1030390 (Mittel).JPG
    102.8 KB · Views: 178
  • P1030389 (Mittel).JPG
    P1030389 (Mittel).JPG
    134.1 KB · Views: 196
  • P1030388 (Mittel).JPG
    P1030388 (Mittel).JPG
    175 KB · Views: 183
  • P1030387 (Mittel).JPG
    P1030387 (Mittel).JPG
    110.4 KB · Views: 184
  • P1030386 (Mittel).JPG
    P1030386 (Mittel).JPG
    161 KB · Views: 186
  • P1030385 (Mittel).JPG
    P1030385 (Mittel).JPG
    176.1 KB · Views: 179
  • P1030383 (Mittel).JPG
    P1030383 (Mittel).JPG
    158.4 KB · Views: 176
  • P1030381 (Mittel).JPG
    P1030381 (Mittel).JPG
    54.9 KB · Views: 181
-mithilfe einer Holzschablone das Leder formen
-im Backofen vortrocknen
-Gürtelasche innen färben, dann kleben
-Naht stechen
-nähen
-innen färben
-Druckknopf einsenken und setzen
 

Attachments

  • P1030392 (Mittel).JPG
    P1030392 (Mittel).JPG
    123.8 KB · Views: 235
  • P1030393 (Mittel).JPG
    P1030393 (Mittel).JPG
    109.6 KB · Views: 202
  • P1030394 (Mittel).JPG
    P1030394 (Mittel).JPG
    152.4 KB · Views: 206
  • P1030395 (Mittel).JPG
    P1030395 (Mittel).JPG
    122.8 KB · Views: 215
  • P1030396 (Mittel).JPG
    P1030396 (Mittel).JPG
    155.3 KB · Views: 225
  • P1030416 (Mittel).JPG
    P1030416 (Mittel).JPG
    177.7 KB · Views: 209
  • P1030417 (Mittel).JPG
    P1030417 (Mittel).JPG
    159.4 KB · Views: 213
  • P1030418 (Mittel).JPG
    P1030418 (Mittel).JPG
    147.6 KB · Views: 213
  • P1030419 (Mittel).JPG
    P1030419 (Mittel).JPG
    169.1 KB · Views: 233
-Druckknopfabdeckung ausstanzen und einkleben
-Blatt zusammenkleben
-zuschneiden
-Naht senken, anzeichnen und nähen
-Kante fasen und polieren
-Druckknopf für die Lasche setzen
-alle Kanten nochmal nachpolieren
-färben, Kantenfarbe auftragen
-fetten, Fertig!
 

Attachments

  • P1030428 (Mittel).JPG
    P1030428 (Mittel).JPG
    99.7 KB · Views: 267
  • P1030427 (Mittel).JPG
    P1030427 (Mittel).JPG
    60.5 KB · Views: 210
  • P1030426 (Mittel).JPG
    P1030426 (Mittel).JPG
    168 KB · Views: 207
  • P1030425 (Mittel).JPG
    P1030425 (Mittel).JPG
    177.1 KB · Views: 197
  • P1030424 (Mittel).JPG
    P1030424 (Mittel).JPG
    215.1 KB · Views: 201
  • P1030423 (Mittel).JPG
    P1030423 (Mittel).JPG
    173.4 KB · Views: 205
  • P1030422 (Mittel).JPG
    P1030422 (Mittel).JPG
    189.6 KB · Views: 188
  • P1030421 (Mittel).JPG
    P1030421 (Mittel).JPG
    124.2 KB · Views: 201
  • P1030420 (Mittel).JPG
    P1030420 (Mittel).JPG
    171.1 KB · Views: 215
  • P1030429 (Mittel).JPG
    P1030429 (Mittel).JPG
    106.7 KB · Views: 246
Last edited:
Hallo Nils -

sehr anschaulich gemacht - die Bilder mit den Werkzeugen und der knackig kurze Text.
Bitte mehr davon :super:

Herzliche Grüße aus Stuttgart,
Jost
 
Hallo,
lese "Shapeholder" und "WIP" das erste Mal, Suchfunktion führte nicht zu Heile, - was bedeutet das ?
Danke
 
Back